9YG-2.24D S9000 Classic Round Baler — Net-Wrap Trailed Hay Baler

14–18% moisture target, dense bales

Lower density preserves leaf retention

Post-combine cleanup, livestock bedding

Paddy clearing, biomass feedstock

Tougher stems, full-density setting

Mixed grass-legume blends

Higher-moisture, paired with wrapper

Dense bales for power-plant intake

An in-house dual cross-joint drive shaft articulates to ~75° (vs ~50° on a single-joint shaft) — eliminating the driveline jam that plagues trailed balers when turning tightly inside small plots. The added safety torque shaft slips on overload, protecting the gearbox and chamber from impact damage.

H-type ferrule fittings carry higher working pressure than the conventional flare fittings used on entry-tier balers. Result: chamber door open–close cycles are noticeably quicker, which compresses the dead time per bale and adds 5–8 bales per operating hour at peak throughput.

A dedicated buffer cylinder dampens the rear chamber's closing impact, cutting peak shock load to the frame and chamber pivots by roughly 60%. Net effect over a 1,500-bale season: fewer cracked weld points and longer pivot bearing life.

An upgraded gearbox carries higher transmission torque, so the baler tolerates dense, heavy windrows without protective declutching. Critical when feeding wet alfalfa or tough corn stover — both crops where lighter gearboxes are the first failure point.

The rear chamber rotates on a dual-side sprocket chain drive instead of single-side. Power transfers symmetrically across the chamber, so the bale rotates more evenly — translating to cleaner cylindrical bale shape and lower vibration through the frame.

Wide pickup clears the windrow in a single pass, cutting field passes 25–35% versus narrower 1.6–1.8 m pickups in the same HP class. Combined with the lighter Classic frame, this lifts effective hectares-per-hour over the Beyond on small/medium plots.

Steel cutting, drum machining, gearbox build, frame welding, painting and final assembly all run on our own factory floor. No subcontracted bale chamber — that's the single component buyers most often see fail on lower-tier baler imports.

The S9000 Round Baler platform has been in active production for over two decades, with units exported to 40+ countries. Year-on-year refinements (driveline, hydraulic, gearbox) come from real field feedback, not catalog updates.

As a Net wrap round baler with CE certification, every unit ships with the conformity documentation accepted by EU customs. Production is governed by ISO 9001:2015 with full traceability records on frame, gearbox and chamber components.

12 mechanical engineers handle drawing customization — hitch geometry, lighting kits, country-specific PTO standards (540/720/1000 r/min), reflector compliance. Standard custom-drawing turnaround: 3–5 working days.

As an established Agricultural hay baler spare parts supplier, we keep pickup tines, drum bearings, net-wrap mechanism components, hydraulic seals and PTO shafts at the factory. Air freight ships in 5–10 days globally; sea freight in 25–40 days.

Each unit hooks to a test tractor, takes 50 cycles of straw feed, and runs through density and net-wrap timing checks before crating. Test report — including density readings and wrap counts — ships physically with the unit.

The Classic delivers 100–200 kg/m³ via sensor-controlled chamber. At maximum setting, a Φ1.3 × 1.4 m bale lands around 370 kg — dense enough for long-haul transport without re-baling. Density is operator-adjustable from the cab to match crop type.

Output specs are identical. Pick Classic for plots under 30 ha, irregular fields, contractor work with daily moves, or where the lighter 4,312 kg frame is easier on smaller tractors. Pick Beyond for plots over 50 ha and full-shift continuous baling on heavy windrows.

55–100 kW (75–135 HP) at the PTO. Below 75 HP the baler bogs down in dense alfalfa or damp straw; above 100 kW gives no benefit since chamber draft — not engine output — is the bottleneck. PTO must run at 720 r/min nominal.

The Classic is a Large Round Baler — too much frame for sub-60 HP tractors. If you need a Mini round baler for compact tractors (25–60 HP), ask your sales rep for the small-frame catalog; we have separate models built for that power band.

12-month base warranty (frame, gearbox, drum bearings) from delivery; extends to 24 months on orders of 5+ units. Lead time: 25–35 days for in-stock specs, 45–60 days for custom configurations. One unit per 40' HQ container with PTO removed.

Bundle pricing available when ordering complete forage-harvest chains (Mower + Tedder + Rake + Baler + Wrapper). Ask your sales rep for the 5-piece package quote — typical bundle savings range 12–18%.